LOOP LOC CUSTOM COVER MEASURING INSTRUCTIONS                                                                       If your pool is very geometric, or a variation of a rectangle, or oval with known radius measurements, A-B measurements may not be necessary. If your pool is not of a "freeform" design, with free flowing curves, perimeter measurements may suffice*. Draw a sketch of your pool and label all corners of the pool with letters A-?, and provide exact INSIDE of POOL measurements from A to B, B to C, C-D...... Then provide 2 or more cross dimensions, i.e. A-D or B-H;   for example. We should be able to price it with this much. Loop-Loc may require A-B measurements for the manufacture of the cover. If your pool is Freeform, i.e. not a variation on a rectangle; triangulation measurements (A-B measurements) are necessary to reproduce your exact pool measurements on Loop-Loc's computers. Please provide INSIDE dimensions (the innermost edge of  the pool's coping). Please write numbers legibly and dark so they fax well. Note any non-removable obstructions within 2' of pool's edge and width of available decking surrounding pool. BEGIN WITH A FREE HAND SKETCH OF THE POOL ON THE GRID    INDICATE INSIDE POOL DIMENSIONS. INCLUDE DECK AREA, PLANTERS AND ANY OBSTRUCTION WITHIN 3' OF THE WATERLINE. A PHOTO IS NEEDED WHEN ROCKS, WATERFALLS, RAISED WALLS, SPAS OR ANYTHING OUT OF THE ORDINARY EXISTS. ESTABLISH 2 POINTS, "A & B" WITH "A" ON THE LEFT AS SHOWN BELOW.      MARK THESE POINTS IN THE GROUND WITH LONG SCREWDRIVERS.     "A-B" LINE MUST BE AT LEAST 3' AWAY FROM THE POOL'S EDGE   AND 2/3 THE LENGTH OF THE POOL; 20-25' IS TYPICAL.    THE A & B POINTS MUST NEVER INTERSECT THE POOL LINE.  INDICATE LOCATION OF A & B POINTS, AND THEIR  DISTANCE APART ON THE DRAWING. ONCE AGAIN, A LINE DRAWN STRAIGHT THROUGH POINTS A-B MUST NOT INTERSECT THE EDGE OF THE POOL ON EITHER END OF THE LINE. USING CHALK OR DUCT TAPE, MARK AND NUMBER THE POINTS ALONG THE INSIDE EDGE OF THE POOL AT APPROXIMATELY 3' INTERVALS. MARK AND NUMBER ALL  LADDERS, HANDRAILS, GRABRAILS, SLIDE LEGS, ROCKS, STEPS, FILL SPOUTS AND DIVING BOARD STAND IF THEY ARE NOT   REMOVABLE, OR IF THEY ARE WITHIN 18" OF THE POOL'S EDGE. MARK AND NUMBER BOTH SIDES OF A SPA WALL AND SPILLWAY, AS SHOWN BELOW. 1'-2' INTERVALS SHOULD BE USED IN SMALL OR TIGHT RADIUS AREAS AND RAISED WALL AREAS. STRAIGHT RUNS OF THE POOL EDGE CAN USE 4' INTERVALS. INDICATE LOCATION OF ALL POINTS AND NUMBER THEM ON THE DRAWING. AN AVERAGE SIZE POOL MAY NEED ONLY 35-45 POINTS. ROUND OUT YOUR MEASUREMENTS TO THE NEAREST INCH (do not write a measurement as 34' 5-1/2", but rather, 34'5) MEASUREMENTS ARE NOW TAKEN FROM POINT "A" TO POINT #1, THEN TO POINT #2, AND ALL THE WAY AROUND THE POOL (TO PT 66 IN THE EXAMPLE BELOW). THEN MEASURE FROM POINT "B" TO SAME POINT #1 AND THEN #2, AS YOU DID FROM POINT "A". MEASUREMENTS ARE WRITTEN IN THE COLUMNS  ON PAGE 2. TAKE MEASUREMENTS BETWEEN 2-4  KNOWN POINTS   TO RECORD POINT TO POINT CROSS DIMENSIONS. RECORD THESE IN THE AREA PROVIDED ON PAGE 2. (for example: point  2 - 32 = 36'1", or point 11 - 47 = 15'3") *NOTE: Loop-Loc makes the determination of the measurements they need to fabricate a cover. A pool that may be fairly geometric may still require A-B measurements for the cover fabrication.     PRINT THIS FORM
A    B             A      B          A      B 1     21     41     2     22     42     3     23     43     4     24     44     5     25     45     6     26     46     7     27     47     8     28     48     9     29     49     10     30     50     11     31     51     12     32     52     13     33     53     14     34     54     15     35     55     16     36     56     17     37     57     18     38     58     19     39     59     20     40     60     POINT TO POINT CROSS DIMENSIONS PT.______ TO PT.______    DISTANCE=_________ PT.______ TO PT.______    DISTANCE=_________ PT.______ TO PT.______    DISTANCE=_________ PT.______ TO PT.______     DISTANCE=_________		REQUIRED INFORMATION! RAISED WALL BEGINS @ PT.____   ENDS @ PT.____ POOL TYPE [_]  GUNITE  [_]  PACKAGE  [_]  ON-GROUND _________________________________    Indicate Package or On-Ground Manuf. COPING INFORMATION [_]  ALUMINUM RECEPTOR [_] CONCRETE BULLNOSE [_] CONCRETE PAVERS [_] FLAGSTONE PAVERS COPING WIDTH ___________ IS COPING ROUGH?  [_]YES  [_]NO UnderCover Padding is required on pools with sharp/rough coping DECKING INFORMATIONHOW MUCH DECK? []3 ft  []4 ft  []5+ ft  WHAT TYPE OF DECK?_____________

PROVIDE INSIDE POOL DIMENSIONS ONLY.     SHOW LOCATION OF ALL POINTS AROUND POOL AND SHOW PTS. "A" & "B" IN RELATION TO POOL.   SHOW ALL OBSTRUCTIONS AND PLANTERS. INDICATE LOCATION AND WIDTH OF DECK IN AREAS WHERE IT IS LESS THAN   3' OF DECK IS AVAILABLE.

DISTANCE FROM POINT

"A" TO POINT '' B'' _______

Fax your measurements to Everything4pools.com  (571) 258-1075

PLEASE NOTE: Custom covers from Loop-Loc are not returnable. Please take care when measuring. Mistakes in measuring which produce mathematical impossibilities will be flagged and returned to us from Loop-Loc.
    HOWEVER, mistakes can be made that do not raise mathematical flags. Please measure carefully, and call if you have any questions. We are here to help you with your Loop-Loc Safety Mesh Pool Cover!

CHECK ONE                                   YES   NO

CHECK ONE            YES  NO

1. Are there any non removable        handrails, grabrails or ladders?.......................   [_]   [_]   a. "A-B" dimensions are required to front center of all       rails, blocks, cups and to the points where rails       enter water.   b. Distance rails extend into pool________       Distance rails are set back from pool_________       Type of grabrail: [_] rail  [_] concrete block/Anthony type 2. Are there any raised rail sockets?......................  [_]   [_]       Height of Sockets_________       "A-B" dimensions required to locate sockets 3. Are there any grab rocks?.................................. [_]   [_]      a. If yes, PLEASE SEND PHOTO!       "A-B" front center of each grab rock, and provide width   b. Width of each grab rock__________       Distance grab rocks are set back from pool_______ 4. Is there a removable fillspout?.......................... [_]    [_]   a. Fillspout is:      [_] level with deck       [_] raised       If raised, how high?_________       Distance spout is set back from pool_________   b. Is end of spout below coping?......................  [_]    [_]       Distance into pool________       Distance below coping level_________ 5. Is there a dive stand?...................................  [_]    [_]       Type of stand____________________       Distance set back from pool__________   a. Is diving board stand removable?.................  [_]    [_] 6. Is there a dive rock?....................................   [_]    [_]   a. If yes, PLEASE SEND PHOTO!        "A-B" the sides and front of rock, as       well as the pool wall, using 1' intervals.   b. Distance rock overhangs pool edge________       Distance rock extends below deck level________ 7. Are there slide legs within 2' of pool?...............  [_]    [_]       If yes, give "A-B" dimensions to each leg, and       give the distance each is set back from pool edge. 8. Is there a spa? If yes, PLEASE SEND PHOTO!. [_]    [_]   a. Is spa to be included in this estimate/order?.... [_]    [_]   b. Is separate cover required for spa?.................. [_]    [_]       If yes, distance between pool & spa       at closest point_________   c. Is spa raised above pool level?....................... [_]    [_]       If yes, how high?_________   d. Is spa dividing wall flush with top of coping?.....[_]    [_]       "A-B" DIMENSIONS REQUIRED ALONG SPA       WALL ON BOTH SIDES OF WALL & SPILLWAY.   e. Does spa wall have an open spillway?.............[_]    [_]       If yes, "A-B" dimensions are required to locate   f. Are there any other specific spa cover design instructions?       ____________________________________________       ____________________________________________       ____________________________________________       ____________________________________________

9. Is there a planter or grass area?.......................   [_]      [_]   a. If yes, PLEASE SEND PHOTO,        and give "A-B" dimensions   b. Installation method in planters         anchor in pipe   [_]       Loop-Loc stakes*     [_]       *(number of stakes must not exceed 30% of total       installation for safety/warranty qualifications. 10. Is there a raised wall, raised bond beam       or raised planter?.........................................   [_]      [_]   a. If yes, PLEASE SEND PHOTO!   b. Is wall strong enough to for cover to attach to       it with snap hooks and eyebolts?..................   [_]      [_]   c. "A-B" the beginning and end of the raised       areas, and points along wall, at 1' intervals   d. Height of wall_________       (Please note: all rectangles with more than 6' of       raised wall must be priced as Special Rectangle.)   11. Is there a waterfall or rock formation?...........   [_]      [_]   a. If  yes, PLEASE SEND PHOTO!      "A-B" the beginning, end, front and sides      of the formation, and pool edge, at 1' intervals   b. Distance rocks overhang pool edge_________ 12. Are there varying deck levels?.....................   [_]      [_]   a. If yes, PLEASE SEND PHOTO!       Indicate height of each level change, and "A-B"       each level, including points on risers to show       angle sloping away from pool edge.   b. Treatment preference:     [_] Raised Wall treatment             [_] Up & Over treatment       Loop-Loc will consider design preference secondary to       safety performance, unless otherwise instructed. 13. Is there a wood deck area?........................ [_]      [_]       If yes, please indicate on sketch in grid       Are wood deck anchor flanges required?..... [_]      [_] 14. If pool is ON-GROUND:       Are there varying deck levels?.................... [_]      [_]       If yes, please submit on sketch in grid 15. Is pool COMMERCIAL (over 2,100 sq. ft.)      [_]      [_]       Pool type:           [_] Skimmer         [_] Gutter       If gutter pool, PLEASE SEND PHOTO! and give all       gutter dimensions. 16. Is cover to be made in a Designer Color?....   [_]     [_]       What color?    [_] Blue     [_] Gray    [_] Black       Note: available only in 3' sections, additional charge 17. Are there  specific design instructions? Please specify!       _________________________________________       _________________________________________       _________________________________________       _________________________________________ PLEASE FAX THIS FORM TO: Everything4pools.com  571-258-1075

PLEASE NOTE: Custom covers from Loop-Loc are not returnable